Shower curtain and translucent liner on hooks beside a measuring tape beneath the article title.

Measure the shower opening or usable rod width, then measure down to the intended hem position. Account for the actual hooks and the curtain’s top construction before choosing a finished length. Check the liner separately: it needs to contain water inside the bathing area, even when the decorative curtain hangs outside.

The existing curtain is a useful reference, but it is not proof of the right size. It may have shrunk, come from another bathroom, or always hung a little too short. Measuring the space and hardware lets you replace it without repeating the same fit problem.

Write down the setup before the dimensions

Start with a dry tub and floor. Use a tape measure from a stable position, and get help with high measurements instead of balancing on the tub rim. Note whether you have a straight rod, curved rod, corner arrangement, or ceiling track. Photograph the hooks and the way the curtain attaches.

For an ordinary two-layer arrangement, identify the decorative curtain and the water-containing liner. Some products combine those functions or use a detachable liner. Check the product description before assuming that every fabric curtain needs the same separate liner.

The manufacturer Medline’s measuring guide, on pages 24–25 of its shower-curtain brochure, emphasizes recording hardware and measuring each opening rather than relying on an old curtain. Its commercial ordering increments are product-specific; use the retailer’s instructions for the item you intend to buy.

Measure the width the panels must cover

On a straight rod across a tub or shower opening, record the opening width and the usable hanging span. Keep brackets and end stops in mind. On a curved or corner rod, record the route the hooks actually travel as well as the opening; the straight wall-to-wall distance alone may not describe that route. Ask the curtain supplier how it wants a curved run measured.

A panel stretched tightly across an opening has little room for folds or overlap at its ends. ShowerTown’s sizing guidance therefore calls for a curtain wider than the opening. The amount should suit the product and arrangement, rather than a universal window-curtain fullness formula.

For a simple comparison, a 72-inch-wide panel across a 60-inch opening leaves 12 inches of extra fabric width. That does not create a guaranteed six-inch water seal at each side: folds and where you position the hooks affect the result. Compare that allowance with the supplier’s fit guidance and inspect both ends when the curtain is closed.

Wraparound tubs and unusually wide showers may need an extra-wide panel or a purpose-made arrangement. If you use multiple panels, confirm how their meeting edges will overlap and whether the hardware supports the intended setup. Two widths added together are not automatically the usable closed width.

Measure length with the hooks in the calculation

Choose the intended bottom position for each layer first. For a conventional tub, the liner should hang inside the tub to direct water inward, while the outer curtain may hang outside. Keep hems from bunching on the floor or interfering with entry. Curbless and accessible showers need the curtain arrangement specified for their drainage and access design.

With the actual hooks fitted, measure from where the curtain’s attachment holes will sit down to its intended hem. Also record the distance from the rod to that point. These two notes help you compare a product whose length is measured from its top fabric edge with one specified by its hanging position.

If the listing gives top-edge-to-hem length, include any fabric above the attachment holes. For example, imagine that you want 70 inches from the attachment-hole center down to the hem, and the product drawing shows one inch of fabric above that center. The corresponding top-edge-to-hem length would be 71 inches. This is a calculation example; use the actual product drawing and hook position.

Hookless curtains and snap-in liners can have different top construction. Do not subtract an assumed two-inch hook drop from every listing. If the dimensions are unclear, send the seller your hardware photo and ask which starting point its stated length uses.

Compare the curtain and liner as separate products

Record width × finished length for both layers, including the units and the measurement starting point. Then check the number and spacing of attachment holes, whether your hooks can carry both layers, and any stated manufacturing tolerance or laundering shrinkage. A matching color name does not establish matching dimensions.

A liner that is slightly different in length may be intentional, provided it hangs correctly inside the bathing area. For a proprietary detachable liner, order the compatible replacement specified for that curtain rather than choosing by approximate size alone.

Check the new panels before discarding packaging

Keep the label and return conditions until you have checked the delivered dimensions. Hang the panels on the intended hardware and close them gently. Look at the end coverage, the liner’s position inside the tub or shower, and the clearance at the bottom. The hooks should move freely without pulling the rod or stretching the top edge.

Correct a poor fit before regular use. Avoid cutting a hem, removing weights, or altering a proprietary liner merely to make a returnable item fit. Once the arrangement works, save the product dimensions with your measurement note. For care after installation, see how to position a shower curtain between uses.