
For a replacement cabinet pull, measure from the center of one mounting screw hole to the center of the other. Match that center-to-center distance to the replacement’s specification. The pull’s overall length describes its appearance, but it does not tell you whether the screws will fit the existing holes.
Take the measurements before ordering a full set. Two handles can look nearly identical from the front and still have different mounting dimensions. Conversely, two pulls with the same hole spacing can have quite different lengths and shapes.
Separate hole spacing from the outside dimensions
Liberty Hardware’s FAQ distinguishes overall length from center-to-center spacing and identifies the latter as the dimension used when replacing existing pulls. In a product drawing, look for an arrow between the mounting-hole centers rather than one spanning the ends of the handle.
Record the overall length separately. A longer handle might cover old marks, but it can also extend into an adjacent door’s path. Note projection too: this is how far the hardware stands out from the cabinet face. Consider the space available for your hand and any nearby appliance, wall, or neighboring handle.
A single-hole knob has no two-hole spacing to measure. A cup pull or unusual recessed fitting may use a different mounting arrangement. Check its drawing instead of assuming that every piece sold as a drawer pull attaches in the same way.
Measure the existing holes without changing them
Empty the area around the handle and open the drawer or door so the mounting screws are accessible. For ordinary removable rear-mounted pulls, support the handle from the front while loosening the screws from behind with the appropriate hand screwdriver. Follow the cabinet or hardware instructions if the attachment is concealed or unfamiliar.
Keep the old pull and its screws together. If a screw will not release normally, stop rather than stripping its head or damaging the drawer front. Measuring a replacement should not require enlarging holes, prying off trim, or disassembling a drawer mechanism.
With the pull removed, place a clear ruler across the holes and read between their centers. Repeat the measurement to check it. You can also measure between the centers of the old pull’s threaded openings as a cross-check. Record which item you measured and keep the units with the number.
If the holes are worn, irregular, or hidden by a mounting plate, photograph the front, back, and old fitting. Give the supplier those details before choosing a size. A rounded estimate is a poor basis for ordering a nonadjustable replacement.
Keep metric sizes and inch sizes distinct
Measure with the scale that lets you read the spacing clearly. Then compare the result with the manufacturer’s stated mounting dimension, including any metric specification in the drawing. Product listings sometimes pair an inch fraction with a rounded metric name.
For example, exactly 3 inches equals 76.2 millimeters. A pull specified as 96 millimeters center to center is a different size, even if a shopping filter places both among small cabinet handles. Do not round either measurement to the nearest inch and expect the holes to align.
When a listing’s inch and metric descriptions seem inconsistent, ask the manufacturer which dimension governs the fit and what tolerance applies. An adjustable pull may support a stated range, but that feature must be explicit. Extra holes, slots, or movable posts are not permission to assume every spacing will work.
Check the mounting surface and screws
A matching hole distance is only part of the fit. Compare the new pull’s mounting feet with the old marks or recesses. Check whether a post or locating feature needs a particular hole shape. Liberty’s hardware glossary can help identify the terms used in a product description.
Measure the material the screw must pass through. Some drawers have both a drawer box and an applied decorative front, so the total thickness can differ from that of a nearby door. Do not assume one screw length will suit every cabinet in the room.
Hickory Hardware’s installation guidance notes that thicker drawer construction may require a different screw length. Its supplied screw specification is product-specific. Use the thread and length required by the replacement pull, rather than transferring an old screw solely because it looks similar.
Confirm one replacement before buying the full set
Compare the delivered item and its drawing with your measurement note. Before tightening anything, check that both mounting points line up naturally with the existing holes. Follow the manufacturer’s fitting directions; do not use screw pressure to bend the handle into alignment.
Check hand clearance and open adjacent doors or drawers gently to look for collisions. Inspect whether the mounting feet cover the intended area without leaving an exposed recess. If the fit is wrong, retain the packaging and ask about a compatible replacement instead of modifying the cabinet to suit an uncertain purchase.
Once one pull fits, measure the remaining doors and drawers before multiplying the order. A kitchen may contain more than one spacing. Keep each confirmed size and its compatible screws together; the guide to organizing spare furniture hardware explains how to label those parts for later repairs.

