
On sandpaper, a lower grit number generally means a coarser abrasive, while a higher number means a finer one within the same grading system. A P before the number identifies the FEPA grading system used for coated abrasives. Keep that prefix when comparing products: an identical number in another system does not necessarily describe the same particle size.
The number is a starting point for choosing a sheet, disc, or sanding sponge. The material being worked, the next coating, and the tool’s requirements still determine what belongs in the shopping basket. A pack marked “fine” cannot answer all three questions.
Read the full grit marking
Look on the packaging and the back of the abrasive for a marking such as P120. Record the whole marking rather than just 120. If you are replacing a product used successfully on a project, keep its brand and product line too; grit is only one part of the specification.
Norton’s technical information compares FEPA and CAMI grading in its coated-abrasives section. Its particle-size tables show why the systems should not be treated as interchangeable across the range. A missing P is not enough by itself to identify an unfamiliar product’s system; check the maker’s information.
Avoid converting by guesswork. If instructions specify a particular system or product, use that specification or ask for a manufacturer-supported equivalent. For a delicate finishing task, “the numbers look close” is not a useful compatibility test.
Use coarse and fine as relative descriptions
Within one grading system, an 80-grit abrasive is coarser than a 180-grit abrasive. Coarser grains generally remove material more aggressively and leave a rougher scratch pattern. Finer abrasives are used where less material removal or a finer surface is needed. They do not make every task better simply because their numbers are higher.
Words such as medium, fine, and extra fine help describe a range, but the printed grit marking is the more useful record. Compare the number and grading system when two packages use different descriptive words. A sanding sponge may also have more than one abrasive face, so read how each face is identified.
Do not make a project’s first pass coarser merely because an assortment includes a low number. The starting abrasive should suit the surface condition. A coarse sheet intended for substantial removal can damage a surface that needs only light preparation.
Let the next finish determine where to stop
Norton’s bare-wood guidance explains that the wood and intended finish affect the final sanding choice. That is more useful than adopting one universal last grit for every stain, paint, and clear finish.
Read the coating manufacturer’s surface-preparation instructions before buying abrasives. Distinguish sanding bare material from sanding between coats; those are different jobs. Check any required drying or curing interval before touching a coated surface with sandpaper.
Suppose your project instructions specify P120 followed by P180 on an identified bare-wood piece. Your purchase note should retain that sequence and the finish it serves. It is not a reason to add P40 at the beginning or P400 at the end. This example illustrates following a specification, not a sanding schedule for every wood.
A finer step should address the preceding scratch pattern, rather than merely polishing the tops of deep scratches. If scratches remain, inspect the work and the instructions before jumping to a much higher number. Extra pressure is not a reliable substitute for selecting the appropriate abrasive.
Match the abrasive to the tool and material
After choosing the grit, check the product’s intended material and form. Mirka’s abrasive overview describes how grain, backing, and suitability for wet or dry use differ. A hand-sanding sheet, a cloth belt, and a film-backed disc are not interchangeable supplies. If a backing is described by a letter or code, look up that product’s meaning instead of assuming the code is a universal quality grade.
For a powered sander, copy the required dimensions, attachment type, and dust-hole arrangement from the tool’s instructions. A disc can have the correct diameter and grit yet the wrong attachment. Keep the tool safely disconnected as its manual directs when fitting accessories.
Wet-or-dry labeling also needs context. Use water only when the abrasive, workpiece, and equipment permit it. A water-resistant abrasive does not make an ordinary electric sander suitable for wet use.
Identify old coatings before disturbing them. EPA warns that sanding lead-based paint can create hazardous dust, particularly in pre-1978 homes. Choosing a finer grit does not remove that hazard. Follow appropriate lead-safe guidance and obtain qualified help where needed.
Keep a usable replacement record
Save the packaging with the remaining sheets or write the full product identification on a storage divider. Include grit and system, product line, dimensions, attachment, and the project it was bought for. Keep different grits separated so a similar-colored sheet does not become an unidentified substitute.
Store abrasives clean and dry as the manufacturer directs. If a sheet loses its marking, do not assign it a precise grit from how it feels. For a project that depends on a known specification, use an identified replacement. The broader repair-before-replacing guide can help decide which repair supplies are worth keeping for work you actually plan to do.

